BETAFPV Pavo Pico ELRS Brushless Whoop Quadcopter Ultra-Light 2S Cinewhoop with HD VTX Bracket, F4 2-3S 20A AIO Flight Controller, 1102 14000KV Motor for DJI O3 Air for Cruising Indoors Outdoors

BETAFPV Pavo Pico ELRS Brushless Whoop Quadcopter Ultra-Light 2S Cinewhoop with HD VTX Bracket, F4 2-3S 20A AIO Flight Controller, 1102 14000KV Motor for DJI O3 Air for Cruising Indoors Outdoors

Troubleshooting:
To improve video quality when recording with DJI O3 HD VTX, turn off its electronic stabilization and use GyroFlow stabilization software.
When fixing the HD VTX bracket with M1.4*10 screws, ensure that the nut just touches the shock-absorbing ball.
The Jello effect may occur during the above installation due to 2 reasons:
The VTX bracket is over-tightened with the screw and the rubber dumper is totally deformed. To solve this, make sure that the screw is tightened just enough to touch the shock-absorbing ball and keep the ball and bracket loose.
If It is a large deformation of the frame or quadcopter blades, replace the frame or blades with larger vibrations if necessary.
Note: use acetate tape to bind motor wires and prevent them from drooping and interfering with the propeller’s rotation.

Specification
Items: Pavo Pico Brushless Whoop Quadcopter
Color: Black
Flight Time*: 4min; Note: The flight time is calculated under 8.4V~6.8V.
Wheelbase: 80.8mm
Battery: 2S 450mAh 45C
FC: F4 2-3S 20A AIO FC
Props: GF 45mm-3B black propeller
Motor: 1102 | 14000KV
Weight (No Battery): 73.47g
Frame: Pavo Pico Brushless Whoop Frame
HD VTX: Support DJI O3 Air Unit
RX Version: Serial ELRS
FPV Camera: Support DJI O3 Camera

Package
1 * Pavo Pico Brushless Whoop Quadcopter (Without HD Digital VTX & Camera)
1 * 2S 450mAh Battery
4 * GF 45mm-3B Propellers
1 * USB Parameter Adjustment Cable
1 * 5.8G Copper Tube Antenna Package
1 * VTX Bracket Screw Package
2 * DJI O3 HD Digital VTX Antenna Mount
2 * DJI O3 HD Digital VTX Mounting Bracket
1 * DJI O3 Lens UV Protector
1 * DJI O3 Lens Protective Case

【Ultralight Cinewhoop】Pavo Pico is an ultra-light 2S cinewhoop with a small wheelbase that is not only equipped with 45mm propellers but also the latest F4 2-3S 20A AIO FC which greatly heightens the flying experience. Its design is well-suited for cruising indoors and outdoors alike.
【Split-Design Frame】The split-design HD VTX mounting bracket is compatible with DJI O3 Air Unit module. The side bracket, rubber damper vibration-damping design, lens holder, and antenna have all been reinforced to suppress low-frequency vibration and enhance the safety of HD VTX, ensuring a stable output of high-definition videos. Simply connect the VTX cable and complete the binding process to start flying.
【Frame Material】Ultra-light PP material is used to make the HD VTX mounting bracket, increasing its toughness. Whoop frame is constructed using PA12 material, known for its exceptional impact resistance and effortless installation process. The antenna fixing slot and frame have been fused to reduce damage risk, while the camera’s installation height has been lowered with a protective printed part to limit its movable angle to within 30°.
【Camera Filter】To safeguard the DJI O3 camera lens and maintain consistent high-definition video output during flight, both a lens filter and a lens protection mount are included. With this feature, you can achieve slower shutter speeds or wider apertures when flying. These lightweight filters are crafted from high-quality optical class ensuring optimal image clarity and are too easy to install on the build.
【Battery Slot】The battery slot and HD VTX mounting bracket duct height have been reduced to enhance the overall flying experience. DIY battery fixing methods are also supported, making them compatible with batteries of varying sizes and capacities.